Contents
- Getting started
- Installing
- First setup and pairing the apps
- Lines and card readers
- Messages and calls
- Routing
- eSIM
- Compatibility list
- Network exits and proxy engines
- Hotspot and Wi-Fi
- Telegram bot remote control
- Status light (LED)
- Updates and backups
- Troubleshooting
- Users in the UK
- Comparison with other tools
Docs / 07
eSIM
An eSIM lives on a writable eUICC card (such as 9eSIM or eSTK.me) in a card reader or 4G module. In Cevix you can then download, switch, rename and delete eSIMs, and rotate between them on a schedule.
Every plan can view eSIMs. Switching and rotation need the Basic plan; downloading, renaming, deleting and transferring need the Full plan.
Inserting and reading the card
Put the eUICC card in a reader (a borrowed remote reader works too) or a 4G module. Under Lines, choose the card’s line, open its “eSIM” tab and choose “Load” (in the old layout, LineseSIM). Cevix recognises the card’s brand and shows its EID and free space.
- For a 9eSIM card you can choose “Check if this 9eSIM is genuine”. This sends the card’s EID to the 9eSIM website; Cevix asks you first.
- An eSTK.me dual-chip card is marked “Dual SE”. Once a profile is enabled on one chip, the card uses that chip; one chip is used at a time.
- The line keeps running: for cards in readers, in 4G modules and in the 410’s built-in 4G module, you can read the card, rename, delete profiles not in use and download new ones while the line runs. Only switching the profile in use restarts the line. Where a module or card cannot do this, the page says why and asks you before it stops the line.
Downloading a new eSIM
- Choose “Load” first.
- Choose “Download eSIM”.
- Under “Activation code”, paste the code from your carrier, or upload or paste a picture of the QR code, or take one with the camera. When the browser cannot read the QR code, the gateway reads it; the picture is not kept. If you only have a server address and a matching ID, use “Manual”.
- Fill in “Confirmation code (optional)” only if your carrier gave you one. Choose “Download”.
While it downloads, a checklist appears beside the profile list: Read the card, Contact the eSIM server, Get the profile, Install on the card, Notify the carrier, Done. The current step shows its seconds; you can cancel until the install. When the download ends, the gateway reads the card again by itself, so the new profile shows in the list straight away.
If a download fails, the failed step gives the reason from the carrier’s server and what to do, for example “The provider did not accept this activation code: it may be mistyped, already used or no longer valid.” A small line below shows the raw code (such as “Server answered 8.2.6 / 3.8”) to give your seller if you ask for help.
You can also start from Overview with “Add a line” → “Add an eSIM number”, or paste an activation code or send a QR code picture in Telegram; see Telegram.
Batch download
“Batch download”, beside “Download eSIM”, handles several activation codes at once: paste one per line (with a confirmation code if needed), upload or paste several QR code pictures, or import a CSV file. You check the list, with duplicates removed, before it starts. Each row can name its card, or use “Automatic” to fill the cards you tick in turn, skipping a card without room.
- The table shows each row’s progress as it goes; you can pause, continue and cancel. One failed row does not stop the batch, unless you tick “Stop on the first failure”.
- No profile is enabled by itself, unless you tick “Enable the first downloaded profile when done”.
- After a gateway restart the batch continues from the next row; a finished row is never downloaded twice.
Switching, renaming, deleting
- Enable
- Switches to this eSIM, usually within a minute.
- Disable
- Switches this eSIM off.
- Rename
- Sets a “Nickname” so you can tell it apart.
- Delete
- Asks you once more first.
To delete several at once, choose “Select” above the profile list, tick the profiles (or “Select all”) and choose “Delete selected”. The confirmation lists each profile and any line that loses its SIM, and starts only once you tick that you understand the profiles will be deleted for good. The profile in use cannot be selected. For each profile deleted, the gateway sends its delete notification to the carrier; some carriers release the number only after they get it.
A deleted eSIM cannot be brought back in Cevix. Most carriers make you apply again to download it.
Rotation schedule
When a card holds several numbers, Cevix can switch between them on a schedule, so each number comes online regularly (for example to keep it). Under “Rotation schedule” on the eSIM page:
- “Rotation interval”: every 15 minutes to every 24 hours, or “Custom…”.
- A switch waits while a call is in progress.
- “Rotate to next profile now”, or “Pause”.
You can also switch or rotate with /esim in Telegram; see Telegram.
eSIM transfer (Beta)
Moves a line’s number to another eUICC card, for example from a physical SIM to an eSIM. Start with “Move to another card” on the eSIM page; the line’s page links there too.
For which carriers can transfer and how far each is verified, see the Compatibility list.
- It needs the carrier to support moving a line by TS.43. Only some carriers do so far. No carrier in Taiwan supports it yet.
- Success is not guaranteed. A transfer may fail or need a retry, and the carrier may cancel the line or the number may be lost.
- After a successful transfer, the original SIM card stops working. This cannot be undone in Cevix.
- Cevix accepts no responsibility for any consequence; you proceed at your own risk.
What you need
- The line runs on your own SIM card, and its IMEI is set.
- Another reader holds an eUICC card with room for one more profile, and no line is running on that reader.
Steps
- Device identity: choose “Cevix (default)”, “Android compatible”, “Samsung compatible” or “Automatic”.
- Check: Cevix asks the carrier whether the line can move. This takes up to 90 seconds.
- New card: pick the eSIM card the line moves to.
- Tick “I understand that the original SIM card stops working after the transfer.” and choose “Start the transfer”.
- Some carriers ask you to confirm on their page: choose “Open the carrier’s page”, finish there, then choose “I have finished”. Do not remove either card until this finishes.
- If the carrier asks something during the transfer (such as the last four digits of your account, or to accept its terms), the wizard shows the question and continues once you answer.
- “Transfer complete” means you are done. If you see “Retry”, it is safe to retry.
These options ask the carrier as another kind of phone. This may go against some carriers’ terms of use, and the carrier may refuse, restrict or suspend the number. Read the notice and tick “I have read this and accept the risk.” first. You use these options at your own risk; Cevix accepts no responsibility.